升降平臺鏈條可以根據貨物的提升高度不同調節鏈條的長度,是升降平臺必非常重要的取物裝置,對提高升降機的作業效率,擴大升降機的作業范圍起著重要作用。那么應該如何維護升降平臺的鏈條呢?
1、介紹鏈輪磨損嚴重后,應同時更換新鏈輪和新鏈條,以保證良好的嚙合,舊的液壓升降平臺鏈條上不能與部分新鏈條混合使用,否則容易在傳動中產生沖擊,拉斷鏈條。
Lift manufacturers introduced sprocket wear serious, it should also replace the new sprocket and new chain, to ensure good engagement, the old hydraulic lift can not be mixed with some new chain on the platform of the chain, or prone to shocks in the drive, and pull off chain.
2、升降平臺鏈條在工作中要記得及時加注潤滑油。而潤滑油則必須進入滾子和內套的配合間隙,以便改善工作條件,以減少磨損。
Speaking lift platform lifts the chain manufacturers work to remember to add oil. The lubricant must enter the roller and the inner sleeve with the gap in order to improve working conditions in order to reduce wear.
3、提醒鏈輪裝在軸上應沒有歪斜和擺動,在同一傳動組件中兩個鏈輪的端面應位于同一平面內,鏈輪中心距在0.5米以下時,允許偏差1毫米鏈輪中心距在0.5米以上的時,允許偏差2毫米。但不允許有摩擦鏈輪齒側面現象,如果兩輪編移過大容易產生脫鏈和加速磨損。
Elevator manufacturers remind sprocket mounted on the shaft should be no skew and swing, in the same end face of the two sprocket drive assembly should be in the same plane, the sprocket center distance of 0.5 m below the tolerance sprocket center distance 1 mm at 0.5 meters above the allowable deviation 2 mm. But does not allow the sprocket side friction phenomenon, if two series moves too easily generated and accelerated wear off the chain.
4、升降平臺的鏈條的松緊度應適宜,太緊增加功率消耗,軸承易磨損太松鏈條易跳動和脫鏈。鏈條的松緊程度為:從鏈條的中部提起或壓下,兩鏈輪中心距的約為2%-3%。
Lift manufacturer recommends the tightness of the chain should be suitable lifting platforms, tight increase in power consumption, bearing wear chain is too loose and easy to beat off the chain. Tightness of the chain as follows: Lift or pressure from the middle of the chain, the two sprocket center distance of about 2% -3%.